流感B病毒診斷試劑盒

芬蘭流感B病毒診斷試劑盒

廣州健侖生物科技有限公司

廣州健侖長期供應各種流感檢測試劑，包括進口和國產的品牌，主要包括日本富士瑞必歐、日本生研、美國BD、美國NovaBios、美國binaxNOW、日本積水、日本榮研、美國OSOM、芬蘭、愛思普林、英國Clearview、凱必利、廣州創侖等主流品牌。

芬蘭流感B病毒診斷試劑盒

我司還提供其它進口或國產試劑盒：登革熱、瘧疾、流感、A鏈球菌、合胞病毒、腮病毒、乙腦、寨卡、黃熱病、基孔肯雅熱、克錐蟲病、違禁品濫用、肺炎球菌、軍團菌、化妝品檢測、食品安全檢測等試劑盒以及日本生研細菌分型診斷血清、德國SiFin診斷血清、丹麥SSI診斷血清等產品。

歡迎咨詢

歡迎咨詢2042552662

芬蘭

想了解更多的產品及服務請掃描下方二維碼：

【公司名稱】 廣州健侖生物科技有限公司
【市場部】    楊永漢

【】 
【騰訊  】 2042552662
【公司地址】 廣州清華科技園創新基地番禺石樓鎮創啟路63號二期2幢101-103室

4、免疫組化中抗原修復的*條件是什么？（尤其是微波修復）
關于抗原修復，我試過的修復條件有EDTA熱修復，檸檬酸鈉為緩沖液的微波修復以及高壓鍋修復。從我的實驗結果來看，微波修復其實很不容易掉片子的，而EDTA熱修復和高壓鍋修復是很容易掉片子的。因為掉片子主要是因為加熱過程中產生的氣泡所引起，而微波修復水加熱到沸騰，沾在片子上的氣泡就會少，不會因為小氣泡上串引起脫片。做EDTA修復時，你可以將片子靠的盡量近些，或是在載玻片四周墊些棉花什么的，然后蓋上蓋玻片，這樣修復的話就能夠盡量減少載玻片上小氣泡的形成。我們用的微波修復條件為：2.94 g檸檬酸三鈉溶于1000 ml的水，調PH值至6.0，微波修復10分鐘。你可以試試，時間可以根據需要自己調整。對于檸檬酸修復來說，只要高壓修復時間控制在加閥冒氣后90秒，冷水下終止開高壓鍋蓋，高壓修復和微波修復一樣不掉片子，而且一般高壓修復效果往往更好一點；關于EDTA熱修復，一般說明書上都講的是PH值等于9，實際上我試過，如果單傳用EDTA，很容易掉片子，但是用Tris-EDTA,一般就不會掉片子了，Tris-base的濃度為0.05 mmol/L,高壓和微波修復都可以，PH也等于9。

4, immunohistochemistry in the best conditions for antigen repair what? (Especially microwave repair)
On the antigen repair, I tried the repair conditions are EDTA thermal repair, sodium citrate buffer for microwave repair and pressure cooker repair. From my experimental results, microwave repair is actually very easy to remove the film, and EDTA thermal repair and pressure cooker repair is very easy to swap the film. Because the film is mainly caused by the bubbles generated during the heating process, and microwave repair water heated to boiling, the bubble on the film will be less, not because of small bubbles on the strings caused by the delamination. When doing EDTA repair, you can keep the film as close as possible, or pad some cotton around the slide, and then cover it with a coverslip, which will minimize the formation of small bubbles on the slide. We used the microwave repair conditions: 2.94 g trisodium citrate dissolved in 1000 ml of water, adjust the PH value to 6.0, microwave repair 10 minutes. You can try, time can be adjusted as needed. For the citric acid repair, as long as the high-pressure repair time control in the valve after venting 90 seconds, open the pressure cooker under cold water cover, high pressure repair and microwave repair can not afford the same film, and generally high-pressure repair is often a little better; about EDTA Heat repair, the general instructions are talking about the PH value is equal to 9, in fact, I tried, if the single-pass with EDTA, it is easy to lose the film, but with Tris-EDTA, generally will not drop the film, Tris-base concentration 0.05 mmol / L, high pressure and microwave repair can, PH is also equal to 9.